Wednesday, November 20, 2013

Rocketeer #1 is Finished!



  This machine is one I thought was 100%. However, when using it, the light switch was very touchy - I had to turn the light on & off several times before it would stay illuminated. Since I was going to part out Rocketeer #3, I decided to cannibalize the light assembly for #1.

  Removing the upper lid, I noticed that the bobbin winder return spring and the bobbin winder latch spring were both not working properly. So much for 100%!

  I posted a few days ago how to replace the bobbin winder return spring and I just had to bend the end of the latch spring and reattach it to the latch to remedy those issues.

  I should have made a tutorial on how to replace the light assembly, it turned out to be a bit more complicated than I had envisioned but I didn't take any photos so it would not be too informative.


The easy way is to cut the wires just inside the machine housing and splice the new socket to the existing wiring but I elected to do it the hard way and replaced the socket and wiring as a single unit, threading the wire down to the main connector.

  When I reassembled the 500, I found that it would zig, but not zag.  At full zig zag width, the needle would go full left and come back to center, but not go from center to the right.  Slant-needle Singers only have a paltry 4 mm zig zag to begin with and cutting that in half leaves that function essentially useless.

  I oiled everything I could get at several times, let it sit, ran it at high speed to work in the oil, but nothing helped.  I could manually push the needle to the right, but it would not go there under its own power.

  I spent much of Sunday afternoon and most of Veteran's Day fiddling with that one problem. The service manual was no help, but the diagrams did convince me that the cause was either a binding needle bar vibrating bracket or a binding needle bar driving arm.

  The needle bar vibrating bracket was the most easily accessed, so I tackled it first.  I loosened the collar below the bracket that holds the bracket in place to be sure that the binding was not at this point.  


Of course, being the easiest fix, that was not the problem.

  The needle bar driving arm is an I-beam connected to the needle bar vibrating bracket one end and a forked end connected to the stitch selector. At the end of the lower fork is a thing called a "ball pivot".  From what I can tell, it looks like a metal Tootsie Pop with a round globe on one end and a shaft on the other end that hooks to the bottom fork of the needle bar driving arm.


  The "ball" of the ball pivot sits in a tunnel in the side of the stitch selector and keeps the driving arm aligned.  The ball slides back and forth in the tunnel as the driving arm moves left and right to re-position the needle.
  I had oiled the back side of the ball pivot several times but the oil had apparently not penetrated far enough into the tunnel to lubricate the ball and make it slide freely. To get at the front side of the ball, you need to remove the camstack. Once the camstack is out, the tunnel is visible on the left wall of the stitch selector.


  I tipped the machine on its nose and filled that tunnel with sewing machine oil and let it sit for an hour. When I next tested the machine, the zig zag was still at 2mm.  I put pressure on the needle bar driving arm to encourage it to move the needle to the right and after a minute of running the machine and adding pressure, the zig zag opened up to its full 4mm.



  That was about 7:30 last night and I am glad I didn't have to go to bed with that on my mind.


Friday, November 15, 2013

Singer Stylist 533



A lady dropped this by the shop last Saturday. She had picked it up for her daughter and wanted it checked out before she gifted it.  It's easy to see why she was attracted to it, it looks pristine. The throat plate doesn't have a scratch on it!  Either the previous owner was very careful and never broke a needle or the machine was used very little.

Only two external issues - the spool pins and one deteriorated bed cushion.


The spool pins had been replaced with the wrong size and were loose in their sockets.  Easy fix, just press in the proper pins.  I had a replacement bed cushion in my parts bin and replaced the bad one.

Opening the top, I was surprised that there were no plastic gears up there, a timing belt transfers rotation from the upper section to the lower.

Then, I opened up the lower section. OOPS! Wish I hadn't done that.


  The formerly white feed gears are dark yellow.  They have no cracks or chips at this point, but once they turn color, it's just a matter of time.

The formerly white hook gear was worse.


It has turned brown and one tooth is chipped partially off. With any use, I predict this gear won't last another six months. I can buy replacement gears like the original but suppliers are now stocking gear sets with curved teeth that are supposed to provide smoother, quieter operation. I am anxious to try out a set of those new gears.

The Stylists are good utility machines, although a but stodgy in the styling area. Maybe Singer should have called them something else like Boxy or Clunky.  Their weak point is the internal plastic gears that are disintegrating with age. It would be nice to find metal replacement gears, then those Stylists would last as long as Singer's 66's.

Tuesday, November 12, 2013

Rocketeer Bobbin Winder Latch Spring

  As I was reassembling the bobbin winders on my three 500's and the 503, I noticed that on only one of the four machines did the bobbin winder latch remain snug against the bobbin winder. It was a little difficult to see why, but investigation revealed that there is a spring under the bobbin winder latch that is supposed to push the bobbin winder latch up against the bobbin winder.


That spring is hard to see because it is so small and hidden under the latch.  I see only two functions for this spring:

 - It keeps the bobbin winder latch from rattling during machine operation

 - It makes the latch snap into place if the operator engages the bobbin winder by pushing the bobbin winder toward the balance wheel but the instruction manual says to engage the bobbin winder by pushing the latch
toward the bobbin and not by pushing the bobbin winder itself.

  Fortunately, I cannot see any adverse effect on machine  performance but if the designers felt it should be there, I want to restore it to original condition.


   The spring is a simple affair having about 1 1/2 coils with an "L" bend at each end. one "L" hooks on a finger beneath and behind  the latch and the other hooks over the back side of the latch.


 The spring  is not as heavy as the bobbin winder return spring and the music wire fishing tackle I bought previously was  close in diameter, so I was going to fashion new springs from it.

  The good news is that none of the springs was broken, they had merely slipped out of place.  Problem as I see it is that the "L" that hooks over the latch is not long enough and eventually loses its grip on the latch.



  A very simple solution - take a pair of needlenose pliers and bend that "L" into a "U".  That should hold in place better than the original design.


Check your Rocketeer bobbin winders to see if there is any spring to the latch when you push it away from the bobbin winder shaft. Since 3 out of 4 of my machines did not offer any resistance, I have to deduce that this must be a common deficiency with this particular design.

NOTE: If you remove the latch, don't lose the washer underneath or the latch will not be able to swivel when reinstalled.


Saturday, November 09, 2013

Singer Rocketeer Bobbin Winder Spring

One of the weak points of the Singer 500a and 503a is the bobbin winder spring.  The spring breaks and the bobbin winder will no longer spring back when the bobbin is filled.  Sometimes, the bobbin winder won't even latch to fill a bobbin.

Fortunately, I had a good spring to use as an example, so I wasn't "flying blind".




Measurements are quite simple and only one is critical - the straight arm of the spring is 3/4" long; the L-shaped arm has a 3/4" long extension, then bends down at a 90-degree angle for another 3/4".  There is only one coil.

For the price of one ready-made spring on the internet, I purchased a 446-foot coil of .029" diameter spring wire. I think I will have enough wire to fashion my own springs for several lifetimes.


I cut off about a foot of wire so that I would have enough to grab onto and wound it around a bolt.  I like to use a bolt because the threads help keep the coils even and straight.


 Then, I cut one arm off at 3/4" and the other at 1 1/2".  I put a 90-degree bend in the long arm and was ready to install.

Unfortunately, I made the coil too small.  This is when I learned that the critical measurement is the coil section - it has to be approximately 1/2" in diameter.


 Larger diameter might work, but I made the first spring with a smaller coil and the bobbin winder mounting screw tightened against the spring and would not allow the bobbin winder to swivel.  It seems counter-intuitive to me, but the coil of the spring must be large enough to remain outside the bobbin winder's swivel arm.


Several more prototypes with unsatisfactory coils.



I finally found a dowel that allowed me to make the correct 1/2" coil and got a good copy of the sample spring.


 If I were going to make many more, I would pick up a larger diameter bolt to wrap the wire around but I only need two right now, so the dowel will suffice.

Wednesday, November 06, 2013

Slant Needle Nose Door Hinge Repair


I estimate that half the slant needle Singers I find in the wild have a broken upper hinge on the nose door.  This is especially true of the 500 series (500a & 503a) but I have also seen it on 401's and 600's. Many of these doors are held on with clear packing tape and that's a band-aid fix but I prefer to have my machines LOOK nice, even if they have been repaired.


So, here is the nose door from the 503 I am rebuilding.  It has the common feature of half the upper hinge broken off and missing, so it cannot just be glued back.  With the broken piece went the hinge pin, so we also have to find a replacement pin. I normally use a finish nail, but this is the shaft out of a pop rivet.


I mix up some epoxy and fill what's left of the channel for the pin.


Next, I position the replacement pin so that it is at the correct angle and press it into the epoxy.  It is best to balance the pin in the slot so that it does not slump down before the epoxy hardens. Then, I slather epoxy over the pin to help hold it in place.


24 hours later, I slice off the excess epoxy and excess pin from the top of the hinge.  I use a rotary tool with a cutoff wheel.  If I applied too much epoxy, now is the time to grind or file it down so it doesn't interfere with the opening or closing of the door.


The original pin is about 1/4" long, but you will find it easier to install the door if you leave the replacement pin a bit longer. With both upper an lower pins the same length, you have to align both with their respective holes to install the door.  If you leave the upper pin longer, you can insert the upper pin and the extra length holds the upper hinge in place while you fiddle with the lower hinge pin.


 TA-DA! the 503 now has a functioning nose door.





Sunday, November 03, 2013

Singer 500 and 503

You may remember the Singer 503a that Jane used for parts to fix up her 500a.


When the smoke cleared, she had no need for a 503 carcass, so she left it for me to use as a parts donor.  Looking at my collection of 500 series slant-needle machines, I see that I have three 500s and no 503, so I think I will sacrifice one of the 500s to build up the 503 and fix some of the other 500s.


From left to right, #1 has a broken bobbin winder spring and a bad light socket;


#2 has a badly chipped nose door,


and #3 is in the least desirable cosmetic condition, with a serious paint scrape beside the stitch length lever and significant wear on the leading edge of the bed. So, it looks like #3 is going to sacrifice a bobbin winder spring and light assembly to #1; a nose door to #2 and some other parts to the 503.

However, that still leaves me short a nose door for the 503 if I don't want to use the one that is badly chipped and a bobbin winder spring. Years ago, I stripped a rusted-out 503 and kept many of the body parts but I can't find them in my mess.  If I don't find those parts, I will have fodder for two more blog posts - repairing the hinge on the nose door and making a bobbin winder spring.

Wednesday, October 16, 2013

I'm Afraid to Open This Featherweight

The covering is coming off the box, both latches are broken, it is held closed by an old belt and the owner warned not to pick it up using the handle.


Well, lifting the lid was a pleasant surprise - a nice assortment of accessories



 including a hemstitcher with all the associated parts.  You often find these missing the special needle plate.


  Now to look inside OH NO!!! IT'S MUMMIFIED!!!


  Turned out that was just a homemade cover to protect the machine below.  Not that there was much to protect, it has seen lots of use over the years.



The cords had been replaced and the power cord was a full twelve feet long. I wonder if they were plugging it in to the neighbor's wall socket. On further inspection, I see a bit of dirt but no rust, thank goodness.



Cleaning and some Oil and grease got the old gal to spin freely and some minor tension tickles and it sews like it's supposed to.


By the way, you always clean before you lubricate.  If you do it in reverse order, you clean out some of the new oil/grease with the lint.

Not a lot of mechanical work to be done, a new motor belt, new bed cushions and new cushions on the foot control were all the parts needed.

Sunday, October 06, 2013

Singer Genie 354


  I picked up this machine a few weeks ago while I was in New Hampshire to attend my 50th high school reunion. It is a Singer model 354, known as the Genie.


  Not quite the vintage or quality I normally like, but since it was the supposed successor to the Featherweight, I feel it is a "Milestone Machine" and I really should have one in my collection.


  You can see from the views of the exterior, it has led a rough life but I believe it has only been used for mending.  Why do I say that?


 The single bobbin that came with the machine had ELEVEN different colors wound on it - cream, orange, red, purple, light red, dark red, tan, orange, tan, green, and white. Some pieces were so short they could not be seen until I unwound the layers above them.  No decent sewing project could be sewn with those little bits of thread.

  It is missing a few parts, the tough one is going to be the trim piece beside the take-up lever.


If anyone has a Singer 353 or 354 parts machine, I would like to talk to you about this item. It is also missing the plastic cover to the clutch release but the 6620C I just acquired has one I can cannibalize - probably the only part on that machine I can use!

Tuesday, October 01, 2013

Janome Jem 639 and My New Favorite Cleaning Aid

  On my weekly stroll through the local thrift shop, I spotted a sweet little Janome Jem just waiting for me to take it home.  It appeared to be in good condition, the foot control, presser foot, and bobbin case were present so I picked it up in hopes that one of the local quilters would be willing to give me a little more than I paid for a lightweight machine to carry to sew-ins and classes.


  When I got it home, I found it was not just in good condition, it looks like it has never been used!  The sticker on top showing how to wind a bobbin was not even smudged.


  It needed no repairs or adjustments, it sews like right out of the box! The package of three needles that came with the machine is unopened.  The only attachment that came with it was a buttonhole foot, there probably should have been a zipper foot, at least.

  The one detracting feature was the price - written in magic marker on the plastic case.  In the past, I have used headlight lens restorer to remove magic marker from plastic but the headlight lens restorer was downstairs and I was upstairs, so I grabbed something else to try, a magic eraser.


  I had never used one of these but picked one up at the Dollar Store to clean our fiberglass shower stall.  It worked fine there, so I have been trying it out on other surfaces - tile grout, vinyl flooring, metal sewing machines - all with excellent results.  I was hesitant to use it on this shiny plastic machine, fearing it might leave scratches or leave a shadow of the Sharpie price mark.  It cleaned off the mark completely and left nary a scratch in the plastic.


 Now a word about Janome Customer Service. I emailed them asking for a copy of the 639 instruction manual.  Within 6 hours, I had a return email with a pdf attachment titled "639.pdf" but when I opened the file, it was for a 693, not a 639.  I emailed them again and within 6 hours had another return email with the proper instruction manual.  Thank you, Janome Customer Service.